Care & Handling

Please reference this page for helpful video, images and text to help you take care of your vaping pen.  Please send us an email or contact form if you have an idea for us to add to this page.

Using Your New Vape Pen, Electronic Cigarette Battery

Press the button 5 times in 2 seconds to turn on or off!

 How to charge?

ecigs, ecigarettes, electronic cigarettes, vaping supplies, vaping wands, vaping pens, ecigs NZ, ecigarettes NZ, Kiwi ecigs, electronic cigarettes new zealand, electronic cigarettes NZ, electronic cigarettes kiwi,electronic cigarettes auckland, ecigs new zealand, ecigs auckland, ecigarettes new zealand, ecigarettes auckland

Screw the battery as shown above onto our eGo Rapid USB Chargers.

When charging your battery, simply screw the battery clockwise into the USB charger until the light on the charger changes from green to red. When the light is red, the battery is charging. The light on the charger will turn green when the battery is fully charged.

Important notes and safety precautions about charging your EGO battery:

  • DO NOT OVER TIGHTEN THE BATTERIES ON THE CHARGER. Over-tightening the battery in the USB charger can cause the charger or battery to malfunction. Turn the battery slowly only until the light on the charger turns from green to red.

 

Vape Pen Battery Not Firing Against Coil (not vaping)

A fairly common, frustrating problem with vape pens can be that your firing pin on the battery is not touching the metal part on the bottom of your atomiser, cartomiser, or clearomiser tank. The battery needs to make contact with the metal portion of the tank so it can heat up the e-liquid. To fix this issue, you can take a toothpick and rais the battery firing pin up about 1mm, being very careful not to pull too hard. Move around the head of the battery firing pin until the whole pin comes up just a little. This happens when you screw your atomiser, cartomiser or clearomiser tank in too far or too hard. Once you get the firing pin popped up more out of its socket, screw your tank back on. You really only need to screw your tank in so it is just touching the firing pin, so just be careful not to screw the battery into the tank too hard as this can cause the pin to become stuck as before.  The same thing happens when you screw it too hard onto the charger.

How to Fill an MT3 Clearomizer:

How to Clean an MT3 Clearomizer:

 

How to Use Your Snoop Dogg G Pen:

How to Fill a CE4 and CE4S Clearomizer:

 

How to Clean and Dry Burn a CE4 and CE4S Clearomizer:

 

 

 How to Clean and Fill a CE5+

More videos coming….

 

Component Basics:

Batteries:
With the introduction of 1100mAH and 1300mAH batteries and even more powerful and compact batteries being tested, some of this is not as important as it used to be.  The Key to transitioning from tobacco to e-cigarettes is power and a clean atomiser.  If you run out of battery power while you’re out and about you’re screwed. Most chargers these days are USB powered and can be plugged into your car USB port or cigarette lighter port with a USB adapter found in the Accessories section.   An extended 8-10 blinking of your battery LED means it needs to be charged, 4-5 blinks means you’re over heating the atomizer.

Don’t forget – If your battery seems dead, it may just be turned off.  Pressing the button 5 times in 2 seconds will turn it on.  Doing the same will turn it off.  If you hold the battery button in for 5 seconds, it will flash quickly and turn off.  This is a safety measure to save your equipment.

Flooding:
If you get a “gurgling” sound when you draw on your device, you have flooded the atomizer and/or the mouth piece “vapor chamber”.  This means that there is too much liquid in the atomizer for it to properly vaporize.  Remove the atomizer from the battery and cartridge and blow out the excess liquid onto a paper towel from the cartridge end.  Also blow out the cartridge from the mouth piece.

E-Liquid:
Some people new to vaping say that the flavors of the liquids are too faint or all taste the same.  Give it some time.  After being off tobacco cigarettes for a few days, your taste buds will start to recover and the flavors will become more distinct.  After a while, you’ll start to notice all of the subtle tastes and smells you’ve been missing all of this time!  If you like, you can change your flavors, or mix 1, 2 or more  for a different taste.

How to fill T3s / MT3s Bottom Fill Clearomizer:

Unscrew the bottom assembly from the tube
Hold the T3s / MT3s tube upside down with the drip tip facing down
Fill with 3ml E-Juice by tilting the clearomizer at a slight angle and dripping juice down the inside wall against the outer wall of clearomizer.
Do not put eliquid into the center tube as it will leak out the bottom of clearomizer.
Screw the bottom assembly back onto tube.
Screw onto electronic cigarette device and you’re ready to vape.
How to change the atomizer head on T3s and MT3s Bottom Fill Clearomizer:

Unscrew the bottom assembly from the tube
Remove the T3s / MT3s coil from the base and and simply screw a new coil into the base.
Screw base back onto T3s / MT3s Bottom Coil Clearomizer
Fill with 3ml E-Juice by tilting the clearomizer at a slight angle and dripping juice down the inside wall against the outer wall of clearomizer.
Do not put eliquid into the center tube as it will leak out the bottom of clearomizer.
Screw onto electronic cigarette device and you’re ready to vape.


Scarpe Gucci Meta Prezzo Coach Backpack Michael Kors Outlet Free Shipping North Face Outlet Locations Tom Savage Kids Jersey Coach Outlet Jeffersonville UGGs Boots Stock Symbol Oakley Sunglasses Batwolf Wholesale Mitchell And Ness Throwback Jerseys